Mercurial > hg > freeDiameter
view doc/rt_busypeers.conf.sample @ 1520:5aa6d237b306
Add 3GPP TS 29.561 V16.3.0 (2020-03)
Add AVPs:
- 3GPP-Notification, OctetString, code 110, section 11.3.1
- 3GPP-UE-MAC-Address, OctetString, code 111, section 11.3.1
- 3GPP-Authorization-Reference, OctetString, code 112, section 11.3.1
- 3GPP-Policy-Reference, OctetString, code 113, section 11.3.1
- 3GPP-Session-AMBR, OctetString, code 114, section 11.3.1
- 3GPP-NAI, OctetString, code 115, section 11.3.1
- 3GPP-Session-AMBR-v2, OctetString, code 116, section 11.3.1
- 3GPP-IP-Address-Pool-Id, OctetString, code 118, section 11.3.1
- 3GPP-S-NSSAI, UTF8String, code 200, section 16.3.1
author | Luke Mewburn <luke@mewburn.net> |
---|---|
date | Thu, 09 Apr 2020 13:24:42 +1000 |
parents | 7ee7b95701c9 |
children |
line wrap: on
line source
# This file contains information for configuring the rt_busypeers extension. # To find how to have freeDiameter load this extension, please refer to the freeDiameter documentation. # # The rt_busypeers extension has two purposes. # - when the local peer receives an error DIAMETER_TOO_BUSY from a peer, # this extension catchs this error and attempts to retransmit the query to another peer if it makes sense, i.e.: # * the peer issuing the error is not the peer referenced in the Destination-Host AVP of the message, # * we have a direct link with the peer that issued the error (see parameter RetryDistantPeers below) # # - When a request is forwarded by the local peer, start a timer and if the corresponding answer/error has # not been received within RelayTimeout seconds, either send to another peer or return a DIAMETER_TOO_BUSY # error, depending on the RetryMaxPeers parameter. # # This extension is mainly useful for Diameter agents, for Diameter clients it is recommended to # implement this logic directly in the client application. # Parameter: SkipTooBusyErrors # If defined, this parameter disables the handling of Diameter Errors message with a Result-Code set to DIAMETER_TOO_BUSY in this extension. # When this parameter is defined, the parameter RetryDistantPeer has no effect. # Default: parameter is not defined. #SkipTooBusyErrors; # Parameter: RetryDistantPeers # By default, the extension only retries to send messages if the peer that issued the DIAMETER_TOO_BUSY error is directly connected to # the local peer (not through a Diameter agent). This avoids the situation where the message is sent to a different relay that will deliver # to the same busy peer afterwards. If the parameter is defined, then the extension will also retry sending messages for errors generated in # distant peers. This should increase the chance that the message is delivered, but also can increase the load of the network unnecessarily. # Default: parameter is not defined. #RetryDistantPeers; # Parameter: RetryMaxPeers # This parameter specifies the limit on the number of times a request can be re-sent to a different peer, before the local relay gives up and # forwards the error to upstream. # Default: 0, meaning all possible candidates are attempted before give up. #RetryMaxPeers=0; # Parameter: RelayTimeout # If the value of this parameter is not 0, it specifies the number of milliseconds (1/1000 s) that the local relay waits for an answer to a # forwarded request before considering the remote peer is busy and taking corrective action (similar as if that relay had returned TOO_BUSY status). # Note: this parameter does not apply for requests issued locally. In that case, the extension issuing the request should directly specify the timeout. # Default: 0, meaning that there is no timeout parameter. #RelayTimeout=0;